-
Projektor-Birnen
-
Epson-Projektor-Birnen
-
Panasonic-Projektor-Birnen
-
Hitachi-Projektor-Birnen
-
NEC-Projektor-Birnen
-
Benq-Projektor-Birnen
-
Vivitek-Projektor-Lampe
-
Sony Projector Lamps
-
Optoma-Projektor-Birnen
-
Christie Projector Lamps
-
Viewsonic-Projektor-Lampen
-
Scharfe Projektor-Birnen
-
Mitsubishi-Projektor-Lampen
-
Mini Portable Projectors
-
Projektor-Zusatz
-
RafaelDie Produkteinführung ist sehr Berufs, ist die Service-Haltung sehr gut, ist die Produktqualität hoch und wird fortfahren sich zu stützen.
-
CharlesDas Service-Personal ist, mit einer großen Produktpalette und garantierten Preisen sehr Berufs. Jeder kann ihn wählen. Ich hoffe, dass die Firma besser und besser erhält.
Haus UHP280W 0,8 E19.4 IC SONY Projector Bulbs LMP-C280
Lebenserwartung | 2000hours | Garantie | 90 Tage |
---|---|---|---|
Anwendung | Schule, Büro, Haus, Ausbildung, Geschäft | Produktname | Projektor-Lampen-Birne |
Helligkeit | Hohe Helligkeit mit ursprünglichem Brenner nach innen | Spannung | alles Land |
Niedrige Art | UHP280W 0,8 E19.4 IC | Nennleistung | 280W |
Markieren | UHP280W SONY Projector Bulbs,LMP-C280 Haus SONY Projector Bulbs,E19.4 IC SONY Projector Bulbs |
UHP280W 0.8 E19.4 IC Bare projector lamp SONY Projector Bulbs Original new LMP-C280
UHP280W 0.8 E 19.4 IC SONY projector bare lamp , all items are 100% new and pass the quality checked. And will be packaged in good condition before dispatch. 100% Brand New, Premium quality, high brightness, long life replacement projector lamp. Compatible for VPL-CX276,VPL-CW276,VPL-CX275,VPL-CW275,VPL-CW278,VPL-CX279,VPL-CX278,VPL-CW279
Product name: | Projector Lamp |
Model No. | UHP280W 0.8 E19.4 IC |
Condition: | 100% Brand new |
Type: | Compatible Bare lamp |
Lamp power: | 280W |
Life time : | ≥2000-5000HourS |
Used in the these projector: | VPL-CX276,VPL-CW276,VPL-CX275,VPL-CW275,VPL-CW278,VPL-CX279,VPL-CX278,VPL-CW279 |
Installation: | Easy installation. |
Warranty: | All items have been QC tested and 90 days Warranty at least |
Package: | Each lamp in a single box with foam protection. One pair gloves and instruction inside. |
If you want your Projector Lamps work longer, please Note:
1. Do not allow the projector to overheat; the primary cause of lamp failure is excessive temperature stress.
2. Allow the projector lamp to cool for at least 10 minutes after powering down, and never move the projector during this period or while the lamp is on. The lamp is much more susceptible to damage while it is hot.
3. Operate your projector in a clean, relatively dust-free environment to prevent clogging of fans and air filters. These filters should be cleaned regularly.
4. Allow plenty of space around the projector's fan or exhaust so excess heat can be dispersed properly.
5. Utilize the "economy mode" if it is available with your projector model and is appropriate for your situation. This mode
decreases projector brightness but the lamp will last longer.
6. Never leave a projector in very hot or very cold environments, for example in a car on a summer or winter day.
Installation:
1. Turn off the Projector and unplug the AC power cord.
2. Loosen the screw on the lamp cover with a screwdriver, and then open the lamp cover.
3. Loosen the 2 screws on the lamp with the screwdriver. Hold up the handle, then pull the lamp straight out.
4. Hold the handle of the new lamp and push it in securely until it reaches the end, and then tighten the 2 screws.
5. Close the lamp cover, and then tighten the screws
6. Plug in the AC power cord.